Cal-Royal NALRMA770036 / FNALRMA770036 Rim Alarm Exit Panic Device - For 36" Doors

Cal-Royal NALRMA770036 / FNALRMA770036 Rim Alarm Exit Panic Device - F*or 36" Doors*

Fits same hole pattern as Von Duprin 99 & 98

Features & Construction:For use in institutions, schools, universities, commercial buildings where heavy duty reliable operation is a requirement.

ANSI A156.3, Grade 1 heavy duty exit device

Alarm unit has internal horn. When the push rail is depressed, the horn sounds to provide an audible means of signaling that the door has been opened and violated.

The unit has changeable 2 minute alarm cutoff or manual reset. Preset at factory for 2 minute alarm cut off.

The key switch to turn alarm off is a standard 1cylinder withCkeyway. The alarm operates on one standard 9 volt transistor battery. When battery is weak the horn will emit an intermittent signal.

Alarmed units are supplied with a switch that monitors push rail only. Unit includesEMERGENCY EXIT ONLY ALARM WILL SOUNDdecal for application on door or unit.

Rail assemblies are heavy duty extruded aluminum body with stainless steel push pad and end caps are made of brass, bronze or stainless steel. Rail travels in direction of the door swing.

Trims are thru bolted for additional security.

Conforms & Meets ADA Regulations.

UL Listed for Panic and ULC10C, UBC 7-2-1777 codes. UL Listed for Fire Exit Hardware. 3 hours. (A) label rating on pairs of doors up to 8 0x 8 0 swinging in same or opposite directions.

Uncompromising security and safety in single and double fire exit doors.

Chassis mounted unit construction.

Non-handed and easily reversible.

Available in many different functions. Lever and escutcheon trims are grade 1 construction with clutch free-wheeling mechanism. Rose and escutcheon covers 161 cut out. (See Below)

For Doors: 1-3/4" thick standard optional 2-1/4" thick. 4-1/2" minimum stile width for single or double door application using standard 938 strike and pull lever, thumbpiece and escutcheon trims.

Chassis: Non-ferrous alloy (Panic Grade), steel (Fire Grade). Cover: Brass, bronze or stainless steel. Covers stock hollow metal doors with 161 cut out.

Mounting: Furnished with wood and machine screws. Available thrubolts on request. Thru bolts are included and standard packaging on fire rated devices.

End Cap: Brass, bronze or stainless steel construction.

Hand: Non-handed, center hub.

Latch Bolt:Stainless steel 3/4throw with anti-pick feature.

Spring: Stainless steel throughout.

Strike: 938 packed standard

Dogging Feature: Allen-type key furnished standard on non-fire labeled devices.

Dimensions: Touchbar height to finished floor 41 (1034mm) at center

Touchbar projection: neutral 3-3/8" (92mm), depressed 2-7/8" (73mm)

Center case: 8-1/16" x 2 3/4" x 2 1/2" (205mm x 68 mm x 62 mm)

Model: NALRM7700EO, FNALRMA770036, US32D, US10B

Suggested Architects Specifications All exit devices shall be of touch bar design with smooth operation and be operative over ⅔ of the door?s clear opening width.

All exit devices must be listed under Panic Hardware in the Accident Equipment List of Underwriters Laboratories, Inc.

Where labeled doors are used as exits, they must be equipped with labeled Fire Exit Hardware and UL10C, UBC-7-2-1777 codes.

All springs shall be of stainless steel throughout. All exit devices shall be of chassis mounted unit construction.

All exit devices shall be ANSI A1563.3, Grade 1.

Related Categories

• Cal-Royal Devices